Add to Cart:

Loctite Silver Grade Anti-Seize 76764 453.6g

RM185.00

  • Model: Loctite 76764 453.6g
  • Shipping Weight: 0.5Kgs
  • Manufactured by: LOCTITE


 

 

Loctite Silver Grade Anti-Seize 76764 453.6gLoctite® Silver Grade Anti-Seize. Heavy duty, temperature resistant, pertroleum-based lubricant compound fortified with graphite and metallic flake. Inert, will not evaporate or harden in extreme cold or heat. For use in assemblies to 1600°F (871°C). Guards against rust and corrosion caused by chemicals and weathering. Eliminates galling and cold welding of threaded parts including aluminum and stainless steel. Lubricates threads, gears, chains, cables, sprockets, levers, pivots, rollers, conveyors, oven doors and hinges.

PRODUCT DESCRIPTION
LOCTITE® Silver Grade Anti-Seize Lubricant is a heavy-duty, high-temperature anti-seize thread compound applicable for heavy pressure applications. It can be used in high
temperature areas up to 870°C (1600°F).

TYPICAL APPLICATIONS
Silver Grade Anti-Seize Lubricant is used to lubricate and to permit easy disassembly of assemblies exposed to high temperatures and heavy contact pressures, such as boiler and
oven parts, jet engines, and industrial turbines.

DIRECTIONS FOR USE
1. For best results, ensure part surfaces are clean and free of debris.
2. Apply a light coating of product to parts requiring lubrication.
3. Assemble parts.
4. When part is assembled, wipe away any excess compound.

PROPERTIES OF MATERIAL
Typical                                               Value
Chemical Type                             Synthetic grease
Appearance                               Aluminum (silver) paste
Odor                                                  Petroleum
Specific Gravity                                  1.17 (base)
Viscosity Flow                         similar to Peanut Butter
Flash Point (TCC), ºF                            >200
Particle Size(mm)                                  22.5

TYPICAL PERFORMANCE PROPERTIES

Static Coefficient of Friction
The following chart shows the static coefficient of friction
between controlled mating surfaces subjected to a compressive
stress that approximates the bearing stress acting on fastener
threads under load (60% of proof for a 3/8-16 Grade 5 steel).
Temperature                             Coefficient of Friction
-65°F (-54°C)                                          0.043
68°F (20°C)                                            0.077
1400°F (870°C)                                       0.164

Torque Tension
Tested on degreased 3/8x16 nuts & bolts in a Skidmore-
Wilhelm apparatus. Data reported are the k-factors calculated
from torque @ 5000 lbs tension.

Lubricity “k” Factor                                0.18

CAUTION
Silver Grade Anti-Seize Lubricant is not a high-speed load
carrying lubricant and should not be used on ball or roller
bearings, or on parts where lubrication is critical.

Torque vs. Elevated Temperatures
The following chart shows break and prevail torque values for plain steel 3/8-16 fasteners degreased, coated, pre-torqued to 30 ft-lbs, heat soaked at an elevated temperature for 24 hours, cooled to room temperature and disassembled. (No signs of galling or seizing were visible.)

Temperature                                                             Torque (in-Lbs)                   
                                                       Break                                          Prevail

-54°C (-65°F)                                     270                                                6
22°C (72°F)                                       264                                                6
537°C (1000°F)                                    96                                                7
760°C (1400°F)                                  262                                             160
870°C (1600°F)                                  132                                               89

Corrosion Resistance
Degreased steel specimens (3/8-16 Grade 5 bolts) were treated with an even coating of Anti-seize and assembled into test blocks of aluminum and carbon steel drilled and tapped with 3/8-16 holes. A small amount of Anti-seize was applied under the bolt heads where high bearing stresses are present. The assemblies were placed in a 95°F condensing humidity salt fog chamber for 180 hours. After conditioning, the bolts were removed and inspected visually for corrosion both in the threads and under the bolt heads. There were no visible signs of
corrosion on any of the treated specimens.

The product was tested for corrosive effects on plain copper strips. There was no sign of corrosion, discoloration, pitting or etching upon completion of the test.

Physical Properties (Base)
                                                                                           Typical
                                                                         Value                              Range
Unworked Penetration (ASTM D-217)                     312                              325 to 299
Worked Penetration (ASTM D-217)                        324                              310 to 338
Dropping Point (ASTM D-217) °C                           232
NLGI Grade                                                           1

Wear Resistance
Extreme pressure testing with a Timken Lubricant Tester (ASTM D2509) indicated Silver grade Anti-Seize Lubricant would resist seizure, scoring and wear under adverse pressure conditions. The test on Anti-seize consisted of a rotating spindle loaded and held constant for a ten-minute interval. If no scoring of the test block was noted, the load was increased and the test run. The following chart shows the load at which failure occurred. The load at which failure occurs is then reported to be the fail load. The last acceptable load is considered to the OK load, or non weld load

Load Type                                           Pressured Applied

OK load, lbs                                           47
Fail Load, lbs                                          52
Scar width at failure, mm                          0.83
Stress value at failure,N/mm2 (psi)            65 (9458)

Torque, Galling and Seizing
Five (5) bolts, 3/4”-10 were pre-torqued to approximately 230 ft lbs. (based on elongation) then conditioned for three six hour cycles @ 1050°F with retorquing after each cycle. After heating,
the entire block assembly was exposed to a 20% salt solution for seven days. Break torque didn’t exceed 250 ft lbs. There was no seizing of any nuts during the test. There was no galling
evident on the threads of the nuts or studs.

GENERAL INFORMATION
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the Material Safety Data Sheet (MSDS).

Ordering Information

Part Number      Container Size

80209                4 oz. Net Wt. Brush Can
76732                8 oz. Net Wt. Brush Top
76759                12 oz. Net Wt. Aerosol
76764                 1 lb. Net Wt. Brush-Top
80206                 1 gal. Can
76775                 5 gal. Pail

Storage
Product shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8°C to 28°C (46°F to 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. For further specific shelf life information, contact your local Technical Service Center.

Data Ranges
The data contained herein may be reported as a typical value and/or range. Values are based on actual test data and are verified on a periodic basis.

Note
The data contained herein are furnished for information only and are believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods we have no control. It is the user's responsibility to determine suitability for the user's purpose of any
production methods mentioned herein and to adopt such precautions as may be advisable for the protection of property and of persons against any hazards that may be involved in the handling and use thereof. In light of the foregoing, Loctite Corporation specifically disclaims all
warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose, arising from sale or use of Loctite Corporation’s products. Loctite Corporation specifically disclaims any liability for consequential or incidental damages of any kind, including lost profits. The discussion herein of various processes or compositions is not to be interpreted as representation that they are free from domination of patents owned by
others or as a license under any Loctite Corporation patents that may cover such processes or compositions. We recommend that each prospective user test his proposed application before repetitive use, using this data as a guide. This product may be covered by one or more United States or foreign patents or patent applications.

 

 


This product was added to our catalog on Monday 23 July, 2012.

Your IP Address is: 54.227.76.180
Template designed by Amazone.com.my. Copyright © 2019 Antara Hardware Home Centre Sdn Bhd (D&B D.U.N.S # 86-58-6574) (Co Reg# 722880-T) (GST Reg # 000646324224). Powered by Zen Cart.